Guide · Homeowners · 3 min read · Updated 16 November 2026
Preparing for AGA or Range Cooker Removal: A Checklist
Short answer
To prepare for AGA or range cooker removal, book the right engineer to make the fuel safe, turn the cooker off 24 to 48 hours ahead, have any boiler drained and capped by a plumber, clear the kitchen of food and soft furnishings, and make sure there is a clear route and parking close to the door. Measure doorways for modern range cookers that come out whole.
Book the right engineer for your fuel type
The first step is making the fuel supply safe, and the right person depends on the fuel. Get this booked first, ideally for the day before removal or the same morning, so the team can start straight away. If the engineer finds a problem, such as no isolation valve or a corroded oil line, you still have time to sort it out.
Fuel disconnection costs £75–£150 in most cases. We can arrange it, or you can use your own engineer and simply confirm it has been done.
| Fuel | Who makes it safe | Notes |
|---|---|---|
| Mains gas | Gas Safe registered engineer | Supply capped and tested for leaks |
| LPG | Gas Safe engineer qualified for LPG | Bottles or tank isolated |
| Oil | Oil-competent engineer, commonly OFTEC registered | Oil line isolated, burner removed if needed |
| Electric | Competent electrician | Dedicated circuit isolated and made safe |
| Solid fuel | Householder, then chimney specialist if needed | Fire out, ash cold and cleared |
Cookers with boilers
Many Rayburns, Stanleys and some AGAs heat water or run radiators through an integrated boiler. Before removal, a plumber or heating engineer needs to drain the system, disconnect the flow and return pipes and cap them. If the cooker was the only heat source, plan how the house will be heated and how you will get hot water in the meantime.
Old heating systems can hold sludgy, black water, so expect the drain-down to be messy. Asking the plumber to fit isolation valves on the capped pipes can make a future boiler installation easier. Put down old towels and a dust sheet near the drain point, and keep a bucket handy for the last of the water trapped in the boiler casting.
Your preparation checklist
Work through this list in the week before removal. Most of it takes only a few minutes, but missing one item can delay the start or add cost on the day.
- Book the fuel disconnection and confirm the date
- Turn the cooker off 24 to 48 hours ahead so the castings are cold
- Have any boiler drained and capped by a plumber
- Empty the ovens, warming plates and any storage drawers
- Remove food, utensils, rugs and soft furnishings from the kitchen
- Clear the route from the kitchen to the door and move furniture aside
- Arrange parking for a van as close to the door as possible
- Send photos of the cooker, seals and flue so asbestos risk can be assessed
Access and parking
A dismantled AGA leaves the house as a series of heavy castings, so the route matters more than the doorway width. Steps, gravel, uneven paths and long passages slow every carry. If the van can park on the drive or right outside, the job is quicker and safer. If you live on a narrow lane or in a town centre, tell us about any parking restrictions so the team can plan.
Modern range cookers usually come out whole, so measure the narrowest doorway on the route. Most 90–110cm range cookers pass through standard doors once the handles and any rails are removed, but tight turns in hallways can be a problem.
Protecting the kitchen
The team lays floor protection along the route and around the cooker, but it helps to remove anything fragile from nearby shelves and walls. Insulation dust travels, so close internal doors and cover any appliances or furniture that stay in the kitchen. If you have pets, keep them in another room or out of the house.
Think about what happens after the cooker has gone. The space will usually be dirty, uneven and missing tiles or flooring where the cooker stood. If a new appliance is going in, line up the fitter, flue specialist or builder so the gap is not left open for weeks.
On the day
The team photographs the cooker, checks the fuel supply is safe and the cooker is cold, then lays protection and starts work. Someone should be at home at the start to show the route and confirm what is being removed, and at the end to check the area. You do not need to stay in the kitchen while the work is done.
If anything unexpected appears, such as suspect asbestos or a live connection that should have been capped, the team stops and explains the options before going any further.
Planning what replaces the cooker
Decide what is going into the space before the old cooker comes out. A new range cooker needs the right supply in the right place, which may mean a Gas Safe engineer extending the gas pipe or an electrician running a new dedicated circuit. If you are fitting kitchen units instead, the floor under the old cooker may need levelling and the wall may need plastering where the flue entered.
If the cooker was your main source of hot water or heating, a replacement boiler or immersion heater needs to be in place, or at least booked. Talking to your fitter or heating engineer before the removal date lets them check the space, take measurements and order parts, so the kitchen is out of action for as short a time as possible.
Questions people also ask
How far ahead should I book AGA removal?
Two to three weeks is sensible, especially in busy periods before Christmas and in spring. That gives time to book the fuel disconnection, a plumber for any boiler and asbestos sampling if needed. Shorter notice can sometimes be arranged if the cooker is already disconnected.
Do I need to be home for the removal?
Someone should be there at the start to show the team the cooker, the route and any access points, and at the end to check the finished area. You do not need to stay in the kitchen during the strip-down, which is dusty and noisy work.
What happens to the flue when the cooker is removed?
The flue pipe connected to the cooker is removed. The opening into the chimney or wall is left for the next stage, which might be sealing, fitting a new appliance or adapting the flue. That work should be done by a heating engineer or chimney specialist, depending on the fuel.
Written and checked by the AGA and Range Cooker Removal team. Read our editorial policy.
More guides
How Much Does AGA Removal Cost in the UK?
AGA removal in the UK typically costs £350–£550 for a two-oven model and £450–£750 for a three or four-oven model, including on-site dismantling,…
How Is an AGA Removed? The Dismantling Process Explained
An AGA is removed by dismantling it where it stands. A qualified engineer makes the fuel supply safe, then the team removes the lids, top plate,…
Asbestos in Old AGAs and Range Cookers: What to Check
Older AGAs, Rayburns and other cast-iron cookers may contain asbestos in rope seals, gaskets, insulation, flue pipes or heat shields. You cannot tell…
Should You Sell, Recondition or Scrap an Old AGA?
If your AGA has sound castings, decent enamel and a complete set of lids, it may be worth selling to a reconditioner, which can reduce or offset the…
Get a free aga and range cooker removal quote
Tell us what you need and we'll come back with a clear price.
Request a quote